International Interprotect 750ml
Processing...

International Interprotect 750ml

£34.99 £32.99
You save: £2.00  (5.72%)

plypa403-750x

Qty


Marine Miles:

Marinestore miles reward your loyalty with future discounts at the checkout. 200 miles earned equal a £1 reward discount. T&C’s apply - click here

This item is worth 165 Marine Miles points!

  • Details

Description

Interprotect® is a quick drying, easy to apply two-pack epoxy primer for high performance protection on all rigid substrates. It's two-component application gives excellent anti-corrosive and abrasion resistance properties and it can be used equally above or below the waterline. Not suitable for use below 5ºC. For detailed product information refer to www.yachtpaint.com.

Application Details: - Interprotect

  • Area: Above and below the waterline
  • Finish/Sheen: Matt
  • Thinner/ Cleaner: YTA061 Thinners No.7
  • Number of Coats: 1-5 by brush or roller depending on the substrate and use.
  • Method of application: Brush, Roller.
Drying/ Overcoating Information:
Temperature ºC
Pot Life
Touch Dry
Overcoating Time (Self) Overcoating Time (Antifoul) Immersion Time
Minimum Maximum Minimum
Maximum
Minimum Maximum
5ºC 10 hours
4 hours 10 hours 6 months
10 hours 24 hours 24 hours
-
15ºC 5 hours 2 hours 5 hours 6 months 5 hours 9 hours 18 hours -
23ºC 3 hours 1 hour 3 hours 6 months 3 hours 7 hours 12 hours -
35ºC 2 hours 30 minutes
2 hours 6 months 1 hour 5 hours 8 hours -

Preparation:

WOOD: Sand with 80-280 grade paper depending on the smoothness required. Remove oil from oily woods like teak, using thinners no.9. Change rag frequently. Preserve if required with Intertox.
LEAD: Rub down with an emery cloth or power wire brush. Degrease with Yacht Line Super Cleaner. Pre-prime with Etch Primer.
STEEL: Grit blast to Sa 2½ to 3. An angle grinder can be used in small areas.
ALUMINIUM: Above Waterline: Clean and degrease with Yacht Line Super Cleaner. Pre-prime with Etch Primer. Alternatively mechanically abrade with aluminium compatible sandpaper or low pressure grit blast using aluminium oxide.
Below Waterline: Degrease AND abrade or grit blast as above.
ZINC/ GALVANISED STEEL: Degrease with Yacht Line Super Cleaner. Pre-prime with Etch Primer

Application:
  1. If any filling required use the appropriate product from the Interfill range, after the first coat of Interprotect has been applied.
  2. Ensure all dust is removed with a dust wipe before painting.
  3. Stir individual components thoroughly, add curing agent to the base, stir and leave for 10 minutes for bubbles to disperse.
  4. Apply the following number of coats:- Steel/ Aluminium/ Alloy - above 4, below 5, Lead - 5, Wood - 3.
  • Stir well before use.
  • Mix ratio is 3:1 (base : curing agent) by volume (as supplied).
  • For maximum performance, temperature should be above 10ºC.
  • If maximum overcoating time is exceeded, abrade thoroughly using 180-220 grade paper.
  • Ideally should be applied to bare substrate, but do not apply over conventional (one-pack) coatings.
Coverage: 6m²/ 750ml

HELPLINE: 02380 21 31 46 - www.yachtpaint.com . For Safety Data Sheet please click here.

Product Reviews

★★★★★ ★★★★★
4.00/5 Stars out of 1 Reviews
5
0
4
1
3
0
2
0
1
0
Verified Buyer
(4)
alex@thebissets.freeserve.co.uk | May 28th, 2012
It's International, so it's the best, it's expensive, but you get what you pay for, as they say!